Greenhouse Vegetable Seeding Machine

Lightweight automatic seedling production line

Complete matrix plate-pressing hole-sowing-covering soil and other processes, single machine man-machine touch screen intelligent operation of 750 plates / hour. Equipment material 304 stainless steel production. 3 years warranty ,2 sets of mold ,1800 suction head.

According to different seed and seeding requirements, the corresponding seeding plate and seed suction head are configured.

It can be matched with 288 holes ,200 holes ,128 holes ,105 holes ,98 holes ,72 holes ,50 holes ,32 holes. The seeding plate is matched with the hole plate.

Sowing time a plate, sowing speed 400-500 hours, sowing rate of 95%-98% or more. The use is efficient and convenient, the operation is simple. Perfect after-sales service

How to use vegetable planter correctly?

Vegetable planter in the process of use will appear some common problems, such as: uneven seeding, fertilizer square axis does not rotate, so we need to pay special attention to these two aspects of the problem, to use the planter correctly. Below, make up a small everybody to analyze why can appear this kind of situation, what reason causes?

The seed quantity is not uniform: the reason why the seed quantity of no-tillage planter is not uniform is that the length of the plug wheel on the mouth opening of the seed drainer is different. Or the fixed anchor bolt of the seeding controller is loosened, resulting in large and small seed discharge. The way to deal with this problem is to adjust the opening of the seeding device again, and to tighten the fixed anchor bolt on the seeding quantity controller.

The reason why the square axis of fertilizer discharge is not rotated is that the chemical fertilizer is too wet or too much chemical fertilizer, the particles are too large to block, and the chemical fertilizer can not be applied smoothly into the soil layer. The way to clear is: remove the spiral fertilizer drain. Smashing block fertilizer.

So, how to use the planter correctly? 

These points can not be ignored After the 

1. Planter is connected with the tractor, it should not be skewed.

2. Before planting, try 10~20 meters to the ground, observe the working condition of the planter, and then announce the planting after exceeding the agricultural request.

3. First cross the ground head, in case the ground head hard, resulting in too deep sowing.

4. During planting, we often observe the working condition of the seeding device, the trench opener, the shroud device and its transmission system organization, such as causing blockage, clay, wrapping grass, and the seed covering is not tight, and the cleaning is given in time.

5. The planter works, it is forbidden to retreat or turn sharply. The promotion or landing of the planter should be carried out slowly to prevent damage to the parts.

6. During operation, the seeds in the seed box shall not be less than 1/5 of the capacity of the seed box; when transported or migrated quickly, the seed box shall not be equipped with seeds, let alone other hanging objects.

7.The work of regulating, repairing, lubricating, or clearing grass, which must be done after parking.

What are the main components and functions of vegetable planter?

Do you know what the main components and functions of the vegetable planter are? Below follow the vegetable planter manufacturer small to understand clearly.

I. SCHEDULE PART

1. Automatic computer control, can adjust the parameters to different hole disk.

2. Control is simple, set on, stop automatic button control.

3. The whole electronic eye control, if no hole plate through, the drum will not rotate, will not waste seeds.

4. Kind of box is equipped with vibration part, so that the roller can adsorb seeds better, and irregular shape seeds can also have good effect.

5. Efficient blowing device can blow away excess seeds, leaving only one seed per hole.

6. Drum can be replaced to meet the seeding needs of different hole plates.

II. Part of the loader

1. Double scraper device to ensure uniform coverage of the matrix, there is no excess matrix on the edge of the hole plate;

2. Can be manually controlled on and off, but also suitable for automatic control device;

3. Conical hole pressing device to make the hole plate pressure out of the hole shape, so that seeds fall more easily in the middle of the hole;

4. Scientific two-stage design to make the excess matrix reasonable recovery, clean and non-waste;

5. Equipped with automatic sensing electronic eye, timely control of the earth line on and off to adapt to the speed change;

6. With movable rollers can be easily moved.

III. LANDER PART With the use of disk loader, can transport different substrates, greatly reduce the labor intensity of feeding. IV. Covering soil, sprinkler parts

The amount of overlying soil can be adjusted at will, equipped with optical sensor, automatic perception of the location of the hole plate, accurate soil cover, sprinkling, no waste of matrix.

Hot Tags: greenhouse vegetable seeding machine, China, suppliers, manufacturers, factory, made in China, Greenhouse Film, Greenhouse Rockwool, Greenhouse PolyCarbonate PC Panel, GreenHouses Indoor Farming, aluminum frame cooling pad, greenhouse shading material